A central corneal thickness of 600 μm is thicker than average. However, thickness alone does not determine whether SMILE or SMILE pro is suitable for your eyes. Surgical suitability also depends on your prescription, how much tissue would need to be removed, how much would remain afterward, and the shape and structural properties of your cornea.
If you have been told that your cornea is thick, what matters is how that measurement fits into your surgical plan.
How thick is a 600-micron cornea?
The cornea is the clear tissue covering the front of your eye. Its thickness is usually measured in micrometers, also called microns. A thickness of 600 μm equals 0.6 mm.
Cleveland Clinic gives approximately 540–550 μm as a typical central corneal thickness range in the United States. Compared with that reference range, a central measurement of 600 μm is relatively thick.
Corneal thickness varies from person to person and can also differ depending on where it is measured. A reading of 600 μm is therefore not a standalone criterion for surgery. Your corneal shape and the amount of vision correction needed also matter.
Can I have SMILE or SMILE pro with a 600-micron cornea?
Even if your central cornea measures a relatively thick 600 μm, thickness alone does not establish whether SMILE or SMILE pro is suitable. Your surgeon calculates the tissue needed to correct your prescription and the amount that would remain, while also assessing corneal shape and biomechanics—how the cornea responds to physical forces.
SMILE corrects vision by creating a thin piece of tissue called a lenticule inside the cornea and removing it through a small incision. SMILE pro uses the VISUMAX 800 system to perform lenticule extraction on the same principle. Even when two corneas start at the same thickness, the amount of tissue removed can differ with the degree of nearsightedness and astigmatism and the surgical design.
Why can the same starting thickness lead to different assessments?
A measurement of 600 μm describes the total corneal thickness before surgery. Planning involves calculating how much tissue would be used for correction and how much corneal tissue would remain afterward.
In general, correcting a greater amount of nearsightedness or astigmatism may require removing more tissue. Two people with the same starting thickness can therefore have different amounts of tissue remaining after surgery if their prescriptions differ.
This is why corneal thickness alone cannot tell you how many diopters SMILE can correct. Your surgeon considers thickness together with the planned correction to assess whether enough corneal tissue would remain.
Can a thick cornea still limit my surgical options?
Yes. Thickness is one factor in assessing surgical suitability, but a thicker cornea is not necessarily structurally stronger.
Before laser vision correction, your surgeon evaluates the shape of the front and back corneal surfaces, the distribution of thickness across the cornea, and the cornea’s biomechanical properties. These findings help assess corneal stability as part of surgical planning.
The front and back surfaces matter, too
Corneal topography and tomography provide information about curvature, the elevation of the front and back surfaces, and how thickness is distributed across the cornea.
Even when a central measurement of 600 μm appears sufficient, an area that bulges asymmetrically or shows a pattern of abnormal thinning relative to the surrounding tissue may need further assessment.
The examination therefore looks at the shape of the whole cornea, as well as the thickness at its center.
What does corneal biomechanics tell us beyond thickness?
Thickness describes the physical thickness of corneal tissue. Biomechanical testing, including assessments of corneal stiffness, evaluates how the cornea responds to an external force.
For example, Corvis ST analyzes how the cornea deforms in response to a puff of air and then returns toward its original shape. This provides information about its biomechanical properties that thickness or shape measurements alone cannot fully describe.
Two corneas that both measure 600 μm can therefore receive different surgical assessments because their shape and biomechanical properties differ.
At EYEREUM Eye Clinic, we assess corneal thickness and prescription alongside the front and back corneal surfaces and corneal biomechanics when determining whether laser vision correction is suitable and which procedure may be appropriate.
Could I still be unsuitable for SMILE with a 600-micron cornea?
Yes. Even with sufficient central thickness, surgery may be limited if a high prescription would leave too little tissue after correction, or if the front or back corneal surface shows a possible abnormality.
Biomechanical findings that raise concern also need careful evaluation.
A thickness of 600 μm is one piece of information used to assess SMILE and SMILE pro suitability. The final decision brings together the amount of correction needed, the tissue that would remain, corneal shape, and biomechanical properties.

